Category Science & Technology

Why does a ship float on water?

                  It is a well-known fact that a solid block of iron which may be as small as a needle readily sinks in water but something as big as a ship floats on water. It is interesting to know why it so happen?

                   According to Archimedes principle, the apparent loss in weight of a body totally or partially immersed in a liquid is equal to the weight of the liquid displaced. The centre of gravity of the body and that of the displaced liquid (centre of buoyancy) must lie in the same vertical line which is called the centre line of the body. In the case of a solid iron block, the weight of the liquid displaced is less than the weight of the block — so it sinks. 

 

 

 

 

                   The case is different in case of an iron ship due to its special construction. Its body is shaped in such a manner that it displaces a large quantity of water, and therefore, experiences an upward thrust greater than its weight. Therefore, when it floats on water, its weight is equal to the weight of water displaced by its immersed portion. In other words, when the ship enters the water the volume of the water displaced is much greater than the volume of actual iron immersed, and as a solid it cannot displace more than its own weight of a liquid. The ship sinks only to the extent the weight of the displaced water is equal to the weight of the ship. Thus the remaining portion of the ship stays out of water.

 

What is Doppler Effect?

               When we hear the sound of a police car speeding past us with its siren blaring or a train roaring past another train, we experience something strange happening to the pitch of the sound. The sound seems to get higher as the car approaches and lower as it goes past. This despite the fact that the actual pitch of the sound remains the same; it just seems so because sound waves reach us faster as the car gets nearer. The effect is known as the Doppler Effect after the Austrian physicist Christian Doppler who first studied it in 1842.

               The Doppler Effect is thus described as the apparent change in frequency of sound, light or radio waves caused by the motion of the source, observer or medium. The basis of the ‘Doppler Effect’ is the fact that sound travels in the form of waves. The pitch of a sound depends on its frequency. The frequency is the number of sound waves striking the ear every second. When the source of the sound is approaching, each wave sent out by the source has a shorter distance to travel than the wave that was sent out earlier from a longer distance. Each wave reaches the listener a little sooner than it would have if the source had not been moving. The waves seem to be more closely spaced. They have a higher frequency or higher pitch. As the train passes away the observer, each wave starts a little further away. Each wave seems to be longer than it would ordinarily be. Hence the pitch is lowered.

               

Continue reading “What is Doppler Effect?”

How do detergents perform the cleaning action?

The word ‘detergent’ means any substance that cleans things. But today the word is usually used to mean synthetic or man-made detergents such as washing powders.

A detergent is an organic substance composed of carbon, oxygen, sulphur and hydrogen compounds. When combined with water it helps to clean soiled materials. The ordinary soap is a type of detergent, but it has a different chemical composition. The household detergents, used mainly for cleaning clothes and utensils, come in powder, flake or liquid form.

The first detergent was developed in 1916 by a German scientist called Fritz Gunther. Since then their use has been on the constant increase.

All the detergents contain a basic cleaning agent called a surfactant or surface-active agent. The surfactant molecules attach themselves to dirt particles in soiled materials like cloth etc. They pry the dirt particles from the cloth and surround the particles with a layer of water that allows them to be carried away. The surfactants that are made by treating beef fat or tallow with various chemicals increase the wetting ability of water by lowering its surface tension. The surface tension is the force that keeps water molecules separate and help to move deeper into soiled materials. This helps remove deep-seated dirt particles in fabrics. For example, surfactants also help detergents create lather and suds. Contrary to the popular belief, lather and suds have very little to do with the cleaning ability of a detergent.

Most of the detergents contain many other agents besides surfactants, including bleaches, fabric brighteners, builders and stabilizers. They also contain anti-redeposition agents that prevent removed dirt particles from returning to the cleaned material.

The surfactants can be divided into three main groups: anionic, which become negatively charged ions when in solution; cationic – which form positive ions in solution; and non-ionic which do not become ionized. Detergents may be anionic, cationic or non-ionic or mixture of two or more type of surfactant.

 

Continue reading “How do detergents perform the cleaning action?”

What is an ammeter?

 

 

          The ammeter is an instrument used for measuring electric current. The current is measured in amperes. There are three main kinds of ammeters: (i) moving coil ammeter (ii) moving iron ammeter and (iii) a hot-wire ammeter.

          The moving coil ammeter is like a galvanometer. It has a strip of soft iron which causes to move in the magnetic field created by the current flowing coil. 

 

 

 

 

 

          The moving-iron ammeter has two pieces of iron inside a coil. One of the iron pieces can move. The other piece cannot move. The current passing through the coil produces a magnetic field. The force of the field moves one piece of iron away from the other. A needle attached to the moving piece on a scale indicates the current. These ammeters can measure both direct and alternating current. 

Continue reading “What is an ammeter?”

What is the science of ballistics?

                The ballistics is a branch of mechanics which deals with the motion behaviour and characteristics of projectiles, such as bullets, bombs, rockets and guided missiles. There are three main branches of ballistics, namely; interior ballistics, exterior ballistics and terminal ballistics. The ballistic missile is a ground to ground missile with a parabolic flight path which is propelled and guided only during the initial phase.

                The interior ballistics deal with the motion of a projectile as it travels down the barrel of a weapon, such as a rifle or pistol. The weight of the bullet, the pressure placed on the bullet, the speed at which the bullet moves through the barrel, the barrel’s length and diameter, and the speed at which the bullet leaves the barrel-all affect the flight of the bullet. The interior ballistics of missiles is concerned with the design of rocket engines and the choice of propellants. 

Continue reading “What is the science of ballistics?”

What is a welding torch?

               A welding torch is a mechanical device that produces a hot flame by mixing gases for the welding or cutting of metals. This device is used to join metal surfaces by raising the temperature high enough so as to melt the joining ends and then fuse them with or without a filter metal. After the heat is removed the joint solidifies and fuse permanently. This torch usually produces a flame temperature of 2750°C to 3300°C by mixing acetylene and pure commercial oxygen which is sufficient to melt the metal locally. The torch thoroughly mixes the two gases and has facilities to adjust and regulate the flame. 

               Welding torches are of two types: low pressure torch and high pressure torch. On a low pressure or injector torch, acetylene enters a mixing chamber where it meets a jet of high pressure oxygen. The amount of acetylene drawn into flame is controlled by the velocity of this oxygen jet. In a high pressure torch both the gases are delivered under pressure. The heat generated at the work is controlled principally by the size of the nozzle or the tip fitted onto the torch. The larger the tip, the greater the gas pressure. Small flames are used with thin-gauge metals. Larger flames are necessary for thick metal parts.

               A welding torch mixes the fuel and gas internally and well ahead of the flame. For cutting, the torch delivers an additional jet of pure oxygen to the centre of the flame. The oxyacetylene flame produced by mixed gases raises the metal to its ignition temperature. The central oxygen jet oxidizes the metal, the oxide being blown away by the velocity of the gas jet to leave a narrow slit or kerf. The temperature for the cutting action, once initiated, is maintained by the oxidation of the metal. Nowadays automatic torches have been developed for precision, cutting and welding.